I know I've asked this before....
Does anyone know of a cheap PCIe x1 prototyping board with all lanes isolated? Nearly all extenders I've found don't have that. I have found a Twin Industries board but me thinks $72 is a bit much...
PCIe x1 prototyping board?
-
- XCore Addict
- Posts: 161
- Joined: Sun Jun 12, 2011 11:47 am
-
- Experienced Member
- Posts: 111
- Joined: Sun Mar 06, 2011 11:39 pm
http://www.xcore.com/projects/protoslice
Open files with Eagle (I think) and generate gerbers. Order PCBs from seeedstudio. Cheap service with 5-7 day lead time.
ENIG finish, recommended because of the PCIe edge connector pads, is an extra $16.00.
Open files with Eagle (I think) and generate gerbers. Order PCBs from seeedstudio. Cheap service with 5-7 day lead time.
ENIG finish, recommended because of the PCIe edge connector pads, is an extra $16.00.
-
- XCore Addict
- Posts: 161
- Joined: Sun Jun 12, 2011 11:47 am
Yes, I've seen that one and contacted Folknology already. According to him the JTAG lanes aren't connected through and that's what I actually want as they also aren't pinned out on the header of the slicekit. I haven't done PCB design in 20 years so that's quite a challenge.TSC wrote:http://www.xcore.com/projects/protoslice
Does seeedstudio provide worldwide service?
-
- XCore Legend
- Posts: 1913
- Joined: Thu Jun 10, 2010 11:43 am
What exactly are you looking for in the break out board ? Please supply more details.pstnotpd wrote:Yes, I've seen that one and contacted Folknology already. According to him the JTAG lanes aren't connected through and that's what I actually want as they also aren't pinned out on the header of the slicekit. I haven't done PCB design in 20 years so that's quite a challenge.TSC wrote:http://www.xcore.com/projects/protoslice
Does seeedstudio provide worldwide service?
Nice work Alan ! From the pic of the PCB, concerned if the PCIe fingers in the layout are long enough to allow for proper access (soldering, etc.) to interface to custom designs. It looks like the PCIe edge fingers will be all hidden once docked inside of the PCIe female connectors. It would be nice to have each of the PCIe traces be brought out to a non-plated via with a hole diameter to support a wire-wrap wire.TSC wrote:http://www.xcore.com/projects/protoslice
Open files with Eagle (I think) and generate gerbers. Order PCBs from seeedstudio. Cheap service with 5-7 day lead time.
ENIG finish, recommended because of the PCIe edge connector pads, is an extra $16.00.
-
- XCore Legend
- Posts: 1274
- Joined: Thu Dec 10, 2009 10:20 pm
Actually the patchslice is a better place to start from, but it does not include the JTAG pins as pstnotpd comments
regards
Al
The PCIe connections are tricky to route for low cost manufacture, getting those vias in would be difficult IMHO and with the patch slice unnecessary.Nice work Alan ! From the pic of the PCB, concerned if the PCIe fingers in the layout are long enough to allow for proper access (soldering, etc.) to interface to custom designs. It looks like the PCIe edge fingers will be all hidden once docked inside of the PCIe female connectors. It would be nice to have each of the PCIe traces be brought out to a non-plated via with a hole diameter to support a wire-wrap wire.
regards
Al
-
- XCore Addict
- Posts: 161
- Joined: Sun Jun 12, 2011 11:47 am
Basically a proto/patch slice with all the PCIe connections, including jtag, pinned out.mon2 wrote:What exactly are you looking for in the break out board ? Please supply more details.
Originally because chained slicekits just take up way to much space and I want to stack them, so I could use this for a short flexible interconnect. And right now I'm slowly succeeding in building a "startstack" which I want to try and connect through the TP1 headers to the slicekit. But no JTAG is available on any of the pin headers.