Hello,
I try to run USB-Audio-2.0-Device-Reference-Design-Software(6.1.0)[12.2.0] with XTAG-w under debugger, and it is not recognized by PC.
I do not make any changes in SW, just compile and run 2ioxs confuguration.
P.S. I'm totally newbie, so forgive me a stupid questions.
USB-Audio-2.0-Device-Reference-Design-Software(6.1.0)[12.2.0
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
At the end - looks like I kill my board, now it and does not recognized by PC even w/o XTAG and I don't know how to return it to the factory default state.
Will try to reanimate it tomorrow.
Will try to reanimate it tomorrow.
-
- XCore Expert
- Posts: 968
- Joined: Thu Dec 10, 2009 9:20 pm
- Location: Bristol, UK
Make sure you are running the correct application for the board. See the readme file if you are unsure.
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
First of all, I want to return the board to the initiate (factory) state, because now it is dead.Ross wrote:Make sure you are running the correct application for the board. See the readme file if you are unsure.
I downloaded precompiled image : app_usb_aud_l1_2ioxs.xe from USB-Audio-2.0-L1-Binary(6.1.0)[12.2.0].
Then I run the command prompt, and make:
xflash app_usb_aud_l1_2ioxs.xe
I see:
After that I disconnect XTAG from the board, re-connect board to USB, and...Warning: F03098 Factory image and boot loader cannot be write-protected on flash
device on node "0".
Site 0 has finished.
xflash succeeded
nothing happens.
Thesycon driver does not see the board.
Windows device manager saw "USB Audio Device" with the yellow "!" sign.
Only VBUS Led is lit on the board.
At the device properties I can see the correct VID (20B1), PID (0002), FW Revision (06.10).
Please help me somebody! I cannot move forward!
P.S. If I make: xflash app_usb_aud_l1_1ioxs.xe - everithing works fine! (Of course,at 44/48 Fs only).
So, firmware with UAC1 works, firmware with UAC2 - not, I tried both, app_usb_aud_l1_2iomx.xe and app_usb_aud_l1_2ioxs.xe.
All this happens after I tried to flash the compiled FW from GUI xTime Composer.
-
- XCore Expert
- Posts: 968
- Joined: Thu Dec 10, 2009 9:20 pm
- Location: Bristol, UK
Sounds like you need to re-install the Thesycon driver.
-
- Member
- Posts: 11
- Joined: Tue Aug 02, 2011 3:24 pm
Hi Alex,
I think you have extracted the Evaluation Kit but haven't installed the driver yet. Assuming you haven't changed the path, the driver installation files could be found in c:\Theysycon\TUSBAudio_v2.19.0\EvaluationKit\DriverPackages\release\. You need to run the setup to install the driver.
Hope this works!
I think you have extracted the Evaluation Kit but haven't installed the driver yet. Assuming you haven't changed the path, the driver installation files could be found in c:\Theysycon\TUSBAudio_v2.19.0\EvaluationKit\DriverPackages\release\. You need to run the setup to install the driver.
Hope this works!
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
Thanks.sivakumar wrote:Hi Alex,
I think you have extracted the Evaluation Kit but haven't installed the driver yet. Assuming you haven't changed the path, the driver installation files could be found in c:\Theysycon\TUSBAudio_v2.19.0\EvaluationKit\DriverPackages\release\. You need to run the setup to install the driver.
Hope this works!
The driver was installed, of course, but.... windows........
I'm also think that something happened with the driver, after I flashed 1ioxs (it works in UAC1 that not need the drivers).
I tried to re-install the driver, and after the 3-nd try it starts to work!
So, it was the default firmware, now I will try to make the same with re-compiled FW.
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
OK, it works now, thank you to all.
I tied to change configuration in customdesign.h and it also works.
But, a question from a novice in Eclipse - when i change configuration in the Build listbox (1iocs, 2iomx, 2ioxs) where ther is an implementation of this?
It defines a system variavles, but where these variables are checked?
Can somebody point me?
Thanks.
I tied to change configuration in customdesign.h and it also works.
But, a question from a novice in Eclipse - when i change configuration in the Build listbox (1iocs, 2iomx, 2ioxs) where ther is an implementation of this?
It defines a system variavles, but where these variables are checked?
Can somebody point me?
Thanks.
-
- XCore Expert
- Posts: 968
- Joined: Thu Dec 10, 2009 9:20 pm
- Location: Bristol, UK
They are listed in the Makefile
-
- XCore Addict
- Posts: 139
- Joined: Sun Feb 23, 2014 11:30 am
The line XCC_FLAGS_configname ?
And another newbie question - where CPU is defined?
I want to make simlified design, but with XS1-L6A-64-TQ48-C5, what I should change?
And another newbie question - where CPU is defined?
I want to make simlified design, but with XS1-L6A-64-TQ48-C5, what I should change?